37
Esta publicación cientíca en formato digital es continuación de la Revista Impresa: Depósito legal pp 196802ZU42, ISSN 0378-7818.
Rev. Fac. Agron. (LUZ). 2021, 38: 31-42. Enero-Marzo.
                                                                 Campos et al.  ISSN 2477-9407
metros de resolución espacial. Fue 
necesario interpolar los valores de 
altitud en el MDE, utilizando el 
método spline, para la obtención nal 
de los mapas de elevación y pendiente 
con resolución espacial de 1 m, y 
convertidos al formato oat.
Al  nal,  la  determinación  de  las 
dimensiones del canal de desagüe se 
realizó utilizando el software Canal 
(GPRH, 2020). La información de 
entrada en el software Canal, requiere 
datos referentes al tipo de canal, 
longitud, pendiente, caudal, holgura, 
inclinación del talud, anchura de la 
base,  profundidad  y  coeciente  de 
rugosidad. 
Resultados y discusión
El área de estudio presenta 
pendiente relativamente baja, 
con un valor promedio del 4,3 % y 
pendiente máxima del 18,6 %. La 
pendiente del área es el principal 
factor a ser considerado para la 
elección del tipo de terraza y la faja 
de movimiento de tierras. Como el 
terreno presenta pendiente suave, se 
optó por el dimensionamiento de la 
terraza de base ancha, con un ancho 
en el rango de 6 a 12 metros, lo que 
hace posible establecer el cultivo en 
toda  su  supercie  y  por  ser  de  fácil 
mantenimiento (Pruski et al., 2009).
Los resultados obtenidos referentes 
al dimensionamiento y la marcación de 
las terrazas a nivel se presentan en la 
gura 2. En la gura 2(a) las terrazas 
fueron dimensionadas considerando el 
resultado obtenido en el software  sin 
adecuaciones.  En  la  gura  2  (b)  las 
terrazas se han redimensionado, a n 
Canal software (GPRH, 2020). The 
input information in the Canal 
software requires data regarding the 
type of channel, length, slope, runoff, 
safety clearance, talus inclination, 
base width, depth, and roughness 
coefcient.
Results and discussion
The study area presents a low 
slope, with an average value of 4.3 % 
and a maximum value of 18.6 %. The 
slope of the area is the main factor 
to be considered for choosing the 
type of terrace and its base. As the 
terrain presents a low slope, a wide 
base terrace was used to sizing the 
terraces, with a width ranging from 6 
to 12 meters, allowed to establish the 
crop on its entire surface (Pruski et al., 
2009).
The results obtained in the sizing 
and implementation of the level 
type  terraces  are  presented  in  gure 
2.  In  gure  2  (a)  the  terraces  were 
dimensioned considering the result 
obtained in the software without 
adjustments.  In  gure  2  (b)  the 
terraces have been resized, in order to 
present adequate values for the ridges 
of the terraces, avoiding breakage 
problems.
In  the  rst  data  processing,  the 
heights of the terrace ridges ranged 
from 0.42 to 0.66 m. However, 
these values are not practicable 
in constructive terms, and it is 
necessary  to  adopt  xed  values  to 
facilitate construction and avoid 
errors. In this way, the value of 0.70 
m was considered for the resizing 
of all the terraces in the area, as